Danfoss FC 300 Interbus Instrucciones de operaciones descargar pdf (Pagina 34)

NB!

Must be set to [5]

Stop and trip

for operation with the Interbus option.

[7] Select set-up 1 This option changes the set-up upon reestablishment of communication following a control word

time-out. If communication resumes causing the time-out situation to disappear, par. 8-05

End-of-

time-out Function

defines whether to resume the set-up used before the time-out or to retain the

set-up endorsed by the time-out function. Note the following configuration required in order to

change the set-up after a time-out: Set Par. 0-10

Active set-up to Multi set-up

[9], and select the

relevant link in par. 0-12

This Set-up Linked To

[8] Select set-up 2 This option changes the set-up upon reestablishment of communication following a control word

time-out. If communication resumes causing the time-out situation to disappear, par. 8-05

End-of-

time-out Function

defines whether to resume the set-up used before the time-out or to retain the

set-up endorsed by the time-out function. Note the following configuration required in order to

change the set-up after a time-out: Set Par. 0-10

Active set-up to Multi set-up

[9], and select the

relevant link in par. 0-12

This Set-up Linked To

[9] Select set-up 3 This option changes the set-up upon reestablishment of communication following a control word

time-out. If communication resumes causing the time-out situation to disappear, par. 8-05

End-of-

time-out Function

defines whether to resume the set-up used before the time-out or to retain the

set-up endorsed by the time-out function. Note the following configuration required in order to

change the set-up after a time-out: Set Par. 0-10

Active set-up to Multi set-up

[9], and select the

relevant link in par. 0-12

This Set-up Linked To

[10] Select set-up 4 This option changes the set-up upon reestablishment of communication following a control word

time-out. If communication resumes causing the time-out situation to disappear, par. 8-05

End-of-

time-out Function

defines whether to resume the set-up used before the time-out or to retain the

set-up endorsed by the time-out function. Note the following configuration required in order to

change the set-up after a time-out: Set Par. 0-10

Active set-up to Multi set-up

[9], and select the

relevant link in par. 0-12

This Set-up Linked To

8-05 End-of-Timeout Function

Option: Function:

Select the action after receiving a valid control word following a time-out. This parameter is active

only when par. 8-04 Control

Timeout Function

is set to [Set-up 1-4].

[0] Hold set-up Retains the set-up selected in par. 8-04 Control

Timeout Function

and displays a warning, until par.

8-06 Reset

Control Timeout

toggles. Then the frequency converter resumes its original set-up.

[1] * Resume set-up Resumes the set-up active prior to the time-out.

8-06 Reset Control Word Timeout

This parameter is active only when

Hold set-up

[0] has been selected in par. 8-05

End-of-Timeout Function

Option: Function:

[0] * Do not reset Retains the set-up specified in par. 8-04 Control

Word Timeout Function

, following a control word

time-out.

[1] Do reset Returns the frequency converter to the original set-up following a control word time-out. The fre-

quency converter performs the reset and then immediately reverts to the

Do not reset

[0] setting

8-07 Diagnosis Trigger

Option: Function:

This parameter has no function for LonWorks.

[0] * Disable

[1] Trigger on alarms

[2] Trigger alarm/warn.

7. Parameters FC 300 Interbus Operating Instructions

MG.33.H3.02 - VLT is a registered Danfoss trademark

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 44 45

Comentarios a estos manuales

Sin comentarios

Danfoss FC 300 Interbus Instrucciones de operaciones Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Adaptadores E Inversores De Energía Danfoss FC 300 Interbus