Danfoss VLT 6000 Manual de servicio

VLT®6000 HVAC ContentsIntroduction to HVAC... 2Safety regulations ..

VLT®6000 HVACCompact IP 20 and NEMA 1VLT 6032 - 6042 380 - 460 VVLT 6016 - 6022 200 - 240 VVLT 6032 - 6042 525 - 600 VCompact IP 20 and NEMA 1VLT 6052

VLT®6000 HVACInstallation High voltage testA high voltage test can be carried out byshort-circuiting terminals U, V, W, L1, L2 and L3and energizing b

VLT®6000 HVAC Electrical installation - earthing of control cablesGenerally speaking, control cables must be braidedscreened/armoured and the screen

VLT®6000 HVACInstallation Tightening-up torque and screw sizesThe table shows the torque required when fittingterminals to the frequency converter. F

VLT®6000 HVAC Direction of motor rotationThe factory setting is for clockwise rotation with thefrequency transformer output connected as follows.Term

VLT®6000 HVACInstallation Motor thermal protectionThe electronic thermal relay in UL-approved frequencyconverters has received UL-approval for single

VLT®6000 HVAC Connection examples, VLT 6000 HVACThe diagram below gives an example of a typicalVLT 6000 HVAC installation.The mains supply is connect

VLT®6000 HVACInstallation Electrical installation, control cablesMax. control cable cross section: 1.5 mm2/16 AWGTorque: 0.5-0.6 NmScrew size: M3See

VLT®6000 HVAC Control unit LCPThe front of the frequency converter features acontrol panel - LCP(Local Control Panel). This is acomplete interface fo

VLT®6000 HVACProgramming[+/-] is used for selecting parametersand for changing a chosenparameter. These keys are also usedto change the local referenc

VLT®6000 HVACThe voltage of the frequency converteris dangerous whenever the equipmentis connected to mains. Incorrectinstallation of the motor or the

VLT®6000 HVAC Display modeIn normal operation, any 4 different operating variablescan be indicated continuously: 1.1 and 1.2 and1.3 and 2. The presen

VLT®6000 HVACProgrammingLine 4 says that the frequency converter is in Auto modewith remote reference, and that the mo tor is running. Display mode I

VLT®6000 HVAC Navigation between display modes175ZA697.10HAND LOCAL RUNNING0 ---- 60Display mode I40.0HzAUTO REMOTE RUNNINGFREQUENCY4

VLT®6000 HVACProgramming Changing dataRegardless of whether a parameter has beenselected under the Quick menu or the Extendedmenu, the procedure for

VLT®6000 HVAC Quick MenuThe QUICK MENU key gives access to 12 of themost important setup parameters of the drive. Afterprogramming, the drive will, i

VLT®6000 HVACAll about VLT 6000HVAC Status messagesStatus messages appear in the 4th line of thedisplay - see example below.The left part of the stat

VLT®6000 HVACsame time. The motor will remain stopped untilone of the signals becomes a logic ‘0’.Automatic Motor Adaptation running (AMA RUN)Automati

VLT®6000 HVACAll about VLT 6000HVAC List of warnings and alarmsThe table gives the different warnings and alarmsand indicates whether the fault locks

VLT®6000 HVAC IndexCcontrol panel - LCP... 18Cable clamp...

VLT®6000 HVACIntroduction toHVAC175HA490.13Warning:Touching the electrical parts may be fatal - even after the equipment has beendisconnected from mai

VLT®6000 HVAC Mechanical installationPlease pay attention to the requirementsthat apply to integration and field mountingkit, see the below list. The

VLT®6000 HVACInstallationSide by side/flange by flangeAll frequency converters can be mounted sideby side/flange by flange.d [mm] CommentsBookstyleVLT

VLT®6000 HVAC Installation of VLT 6400-6550 380-460 V CompactIP 00, IP 20 and IP 54Cooling Side-by-sideAll units in the above-mentioned series requir

VLT®6000 HVACInstallation High voltage warningThe voltage of the frequency converteris dangerous whenever the equipment isconnected to mains. Incorre

VLT®6000 HVAC Extra protection with regard to indirect contactELCB relays, multiple protective earthing or earthingcan be used as extra protection, p

VLT®6000 HVACInstallation RFI switchMains supply isolated from earth:If the frequency converter is supplied from an isolatedmains source ( IT mains)