Danfoss VLT HVAC Basic Drive FC 101 Información técnica Pagina 65
- Pagina / 99
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
16-11 Power [hp]
Range: Function:
0.00 hp* [0.00 - 1000.00
hp]
View the DC link power in hp. The
value shown is calculated on the basis
of the actual motor voltage and motor
current.
16-12 Motor Voltage
Range: Function:
0.0 V* [0.0 - 65535.0 V] View the motor voltage, a calculated
value used for controlling the motor.
16-13 Frequency
Range: Function:
0.0 Hz* [0.0 - 6553.5 Hz] View the motor frequency, without
resonance dampening.
16-14 Motor Current
Range: Function:
0.00 A* [0.00 - 655.35 A] View the motor current measured as a
mean value, IRMS.
16-15 Frequency [%]
Range: Function:
0.0 %* [0.0 - 6553.5
%]
View a two-byte word reporting the actual
motor frequency (without resonance
dampening) as a percentage (scale
0000-4000 Hex) of 4-19 Max Output
Frequency.
16-18 Motor Thermal
Range: Function:
0.0 %* [0.0 - 100.0
%]
View the calculated motor temperature in
percentage of allowed maximum. At 100% a
trip will occur, if selected in 1-90 Motor
Thermal Protection. The basis for the
calculation is the ETR function selected in
1-90 Motor Thermal Protection.
3.12.3 16-3* Drive Status
16-30 DC Link Voltage
Range: Function:
0 V* [0 - 65535 V] View a measured value.
16-34 Heatsink Temp.
Range: Function:
0 C* [0 - 255 C] View the temperature of the frequency
converters heat sink.
16-35 Inverter Thermal
Range: Function:
0.0 %* [0.0 - 255.0 %] View the percentage of thermal load on
the frequency converter. At 100% a trip
will occur.
16-36 Inv. Nom. Current
Range: Function:
0.0 A* [0.0 - 655.35 A] View the inverter nominal current, which
should match the nameplate data on the
connected motor. The data are used for
motor protection, etc.
16-37 Inv. Max. Current
Range: Function:
0.0 A* [0.0 - 655.35 A] View the inverter maximum current. The
data are used for calculation of
frequency converter protection, etc.
16-38 SL Controller State
Range: Function:
0 * [0 - 255 ] View the actual state of the Smart Logic Controller
(SLC).
3.12.4 16-5* Ref. & Feedb.
16-50 External Reference
Range: Function:
0.0 %* [-200.0 - 200.0 %] View the total reference, the sum of
digital, analog, preset, bus and freeze
references.
16-52 Feedback[Unit]
Range: Function:
0.0
ProcessCtrlUnit*
[-4999.0 - 4999.0
ProcessCtrlUnit]
View the feedback
resulting from the
selection of scaling in
3-02 Minimum Reference
and 3-03 Maximum
Reference.
Parameters VLT HVAC Basic Drive Programming Guide
64 MG.18.B1.02 - VLT
®
is a registered Danfoss trademark
3
3
- Programming Guide 1
- 1 Introduction 2
- 3 Parameters 2
- Contents 2
- 2 MG.18.B1.02 - VLT 3
- 4 Troubleshooting 4
- 5 Parameter Lists 4
- 4 MG.18.B1.02 - VLT 5
- 1.1.2 Symbols 7
- 1.1.3 Abbreviations 7
- Definitions 8
- 175ZA078.10 9
- Pull-out 9
- MG.18.B1.02 - VLT 10
- High Voltage 11
- 1.1.6 Electrical Overview 12
- 2 How to Programme 13
- 14 MG.18.B1.02 - VLT 15
- Closed Loop Set-up Wizard 17
- Main Menu 19
- * English 21
- * Interna 21
- * Active Set 22
- 3.1.3 0-3* LCP Custom Readout 23
- 3.1.4 0-4* LCP 24
- 3.1.5 0-5* Copy / Save 24
- 3.1.6 0-6* Password 24
- * Variable 25
- * [0.01 - 26.0 26
- * [100.0 26
- * Off No function 26
- 3.2.3 1-3* Adv. Motor Data 27
- 1-4* Cable Length 27
- 3.2.7 1-7* Start Adjustments 28
- 3.2.8 1-8* Stop Adjustments 29
- 3.2.9 1-9* Motor Temperature 29
- 3.4.1 3-0* Reference Limits 31
- 3.4.2 3-1* References 31
- * Analog in 54 32
- * Local bus 32
- * [0.05 32
- 3.4.5 3-8* Other Ramps 33
- 3.5.1 4-1* Motor Limits 34
- 3.5.2 4-5* Adj. Warnings 34
- 3.5.3 4-6* Speed Bypass 35
- 3.6.1 5-0* Digital I/O Mode 36
- 3.6.2 5-1* Digital Inputs 36
- * No operation 38
- * Coast inverse 38
- 3.6.3 5-4* Relays 39
- 5-40 Function Relay 40
- Option: Function: 40
- 3.6.4 5-9* Bus Controlled 41
- 3.7.1 6-0* Analog I/O Mode 42
- 3.7.2 6-1* Analog Input 53 42
- 3.7.3 6-2* Analog Input 54 43
- * [0.0 - 200.0 44
- * [0.0 - 100.0 %] 44
- * 0-20 mA 45
- Options - Group 8 47
- 3.8.1 8-0* General Settings 47
- 3.8.2 8-3* FC Port Settings 47
- 3.8.3 8-5* Digital/Bus 48
- 3.8.4 8-7* BACnet 49
- 3.8.6 8-9* Bus Feedback 50
- 3.9.1 13-** Prog. Features 51
- 13-0* SLC Settings 51
- * Do not reset 53
- * Disabled 53
- * [-9999.0 54
- * [0.0 54
- 13-52 SL Controller Action 58
- * Manual reset 59
- 3.10.4 14-4*Energy Optimising 60
- 3.10.5 14-5* Environment 60
- * [1.0 - 16.0 kHz] 61
- 3.11.1 15-0* Operating Data 62
- 3.11.2 15-3* Alarm Log 62
- 3.12.1 16-0* General Status 64
- 3.12.2 16-1* Motor Status 64
- 3.12.3 16-3* Drive Status 65
- * [0.1 - 9999.0 69
- * [0.0 - 400.0 %] 69
- * [0.0 - 400.0 Hz] 70
- * [0.0 - 100.0 70
- Group 24 72
- 3.16.1 24-0* Fire Mode 72
- Range: Function: 74
- 4.1.1 Alarm Words 77
- 4.1.2 Warning Words 77
- 4.1.3 Extended Status Words 78
- 4.1.4 Fault Messages 78
- 78 MG.18.B1.02 - VLT 79
- 5.1.3 1-** Load and Motor 83
- 5.1.4 2-** Brakes 84
- 5.1.5 3-** Reference/Ramps 84
- 5.1.6 4-** Limits/Warnings 85
- 5.1.7 5-** Digital In/Out 85
- 5.1.8 6-** Analog In/Out 86
- 5.1.9 8-** Comm. and Options 87
- 5.1.10 13-** Smart Logic 88
- 5.1.13 16-** Data Readouts 90
- 5.1.16 22-** Appl. Functions 91
- 92 MG.18.B1.02 - VLT 93
- 94 MG.18.B1.02 - VLT 95
- 96 MG.18.B1.02 - VLT 97
- *MG18B102* 98
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales