Danfoss FP715Si Manual de usuario

FP715 SiElectronic, 2-channel full programmer for heating & hot water with service interval timerInstallation & User Instructions(Including 2

10Table A cont..DANFOSS RANDALL FP715, CP715 (PUMPED)MAINSDHW OFFHTG OFFDHWONNL12 3SANGAMO S409/3 3,6 7 4 2 5SATCHWELL LIBRA & DHP 2201 1 2 8 5 6S

11W HTG ONWires other than links in these terms go to LIVENOTEThis conversion applies only if...An additional terminal block may be required where th

12Table BDANFOSS RANDALL FP715, CP715 (PUMPED)MAINSDHW OFFHTG OFFDNL12DANFOSS RANDALL 922/972 N L 1 4DANFOSS RANDALL 102/102E/102E7 5 3,6 - -HORSTMANN

13DHW ONHTG ONWires other than links in these terms to LIVENOTEThis conversion applies only if...An additional terminal block may be required where t

14Table B cont...DANFOSS RANDALL FP715, CP715 (PUMPED)MAINSDHW OFFHTG OFFDHONL12SMITHS IND. CENTROLLER 1000 N L - -SMITHS IND. CENTROLLER 60 1 2 - -SM

15HW ONHTG ONWires other than links in these terms to LIVENOTEThis conversion applies only if...An additional terminal block may be required where t

16What is a programmer?... an explanation for householders.Programmers allow you to set ‘On’ and ‘Off ’ time periods. Some models switch the central he

17User InstructionsYour programmerThe FP715 Si allows you to switch your heating and hot water on and off at times that suit you. Your programmer has

18Before you startOpen the fl ap on the front of the clock. Press the RESET button using a non-metallic object (e.g. pencil/matchstick) until you hear

19Press DAY/HOL to display day and month. Use the + or - buttons to set the correct month (Jan = 1, Feb = 2 etc.).Press DAY/HOL to display day and m

2Installation InstructionsProduct specifi cation and Installation 3 Installation and Wiring 4DIL switch settings 5Advanced Programming Options 5Cop

20 Before you change the preset programmesYour installer will have set your unit to operate in one of the following modes: 5/2 day - one set of pro

211. Press PROG once until SET CH ON TIME appears at the top of the display and MOTUWETHFR appears at the bottom of the display. Use the + or - bu

22 4. Press the DAY/HOL button once and SASU will appear at the bottom of the display. If the same programme is required press the COPY button a

231. Press PROG once until SET CH ON TIME appears at the top of the display. Note the current day is displayed. Press the DAY/HOL button until the req

246. Press the PROG button twice to return the unit to RUN mode (time appears & colon in the display begins to fl ash). 7. Proceed to page 27

251. Press PROG once until SET CH ON TIME appears at the top of the display. Use the + OR - buttons to set the time you want your heating to fi rst co

26To set the hot water programme press the PROG button twice until SET HW ON TIME appears on the display.Set the hot water programme in the same way a

27Running your Programme To run the central heating programme: press the SELECT button next to the radiator symbol until AUTO is displayed in the LC

28 The grey buttons next to the radiator symbol are the Heating override buttons. The grey buttons next to the tap symbol are the Hot Water override

29Holiday ProgrammeHoliday ModeTo automatically bring the heating back on when returning from holiday the FP715-Si has a built in holiday feature.Foll

3Installation & Specifi cationPlease Note: This product should only be installed by a qualifi ed electrician or competent heating installer, and sho

30This is handled automatically. Should the installer have turned off Automatic Time Change then follow the instructions below.Open the fl ap on the fr

31Service Interval TimerService Interval Timer If the property is owned by a landlord he may, for gas safety reasons, have instructed the installer

32If it is necessary to fully reset the unit, excluding the date and time, follow the instructions below.1. Press and hold the +1HR and MAN buttons o

33Fault Check ListTroubleshooting

34

35

36Danfoss Randall LtdAmpthill RoadBedfordMK42 9ERTel: 01234 364621Fax: 01234 219705Part No 38068v09s7.06 09/10Still having problems?Call your local

4NL1234230VFused 3AOFFDHWOFFHTGONDHWONHTGELECTRONICSN/ON/CN/ON/C The wallplate must be securely mounted either directly to the wall using suitable w

5Not UsedGravity5/2 Day7 DaySw.1Sw.2Sw.3Sw.4Not UsedPumped7 Day or 24 Hour24 HourDIL switch settings and Advanced Programming OptionsTick the INSTALLE

6Copy Functions ExplainedThere are 3 possible copy functions available. These are; Standard Copy, Enhanced Copy, and AB copy. Copy functions are enabl

7Service Interval TimerThe FP715 Si is fi tted with an installer setback service interval timer. If this feature is required please contact our technic

8Wiring Conversions, (applies only to 230 volt models) Wiring conversions can be used when replacing the following programmers with the FP715 Si. Some

9Table B (pages 12-15) should be used. If in any doubt, contact our Technical Services Department before proceeding with the replacement. *Any wires c