Danfoss FP735Si Guía de instalación

FP735SiElectronic 3-Channel Full Programmer for Heating and Hot Water with Service Interval Timer Danfoss HeatingMAKING MODERN LIVING POSSIBLEInstalla

FP735SI10GBGB6.0 Display InformationChannel Status(Event number when programming)Channel NumberTIMEDays of Week (Numbers or Text)KEY TO SYMBOLSFlame:

Danfoss Heating11GBTo access the Advanced Programming follow the steps below: a) Press and hold PROG and V for 5 seconds. The display will chang

FP735SI12GBIn the Advanced Programming mode, the following parameters can be changed:Parameter1 – Enable/Disable A+B DaysThis allows the unit to opera

Danfoss Heating13GBParameter 6 – Operating Mode(7 Day, 5+2 Day or 24 Hour) This parameter sets the unit to operate using either 7 day, 5+2 day or 24 h

FP735SI14GBParameter 7 – Keyboard LockThis parameter sets the unit to operate with an enabled (functioning) or a disabled (locked) keyboard.Press + un

Danfoss Heating15GBTo perform a standard copy operation: a) Press CH to select the channel.b) Press PROG to go to event programming.c) Press DAY/HOL t

FP735SI16GB10.0 The Information KeyWhen running in normal operation, the Information key COPY/i will provide the following information:1st COPY/i key

Danfoss Heating17GBThis does not reset any programmes or the time or date, but will cancel any manual overrides that have been selected. 11.2 Full Res

FP735SI18GB3on 2on 2o1on 1oL NLinks to be made by installer10 16 9 L NPermanent linksWiring Box - WC4B1 23456789101112 13 14 15 16 L N32321 2 4L 3NC

Danfoss Heating19GB16 1321 2 4L 3NCOM CALL NRoom Thermostat - Zone 2RET BRMT230RET2305 N 67Brown Blue Orange GreyOut InHP22 2 Port Valve (Heating Zone

FP735SI2GBFor a large print version of these instructions please call Marketing on 0845 121 7400.Danfoss can accept no responsibility for possible err

Part No. 013R9577/VIHVC202 - 03/2014Danfoss Ltd.Ampthill RoadBedford MK42 9ERTel: 0845 1217 400Fax: 0845 1217 515Email: [email protected]:

Danfoss Heating3GBGBIndex1.0 Installation Guide ...42.0 System Overview

FP735SI4GBGBTimer Features FP735SiPower supply 230V, 50HzMemory backup Retained for the life of the productFactory set calendar clock Automatic summe

Danfoss Heating5GBGB3.1 First remove the wallplate from the back of the unit.3.2 From the top left hand corner of the wallplate, there must be cleara

FP735SI6GBGBFP735Si is delivered with a set of parameters that have been pre-programmed to cover the most typical type of installations. See (5.0). If

Danfoss Heating7GB4.2 Advanced ProgrammingAdvanced Programming is meant for changing certain parameters that are usually only set once. Advanced Progr

FP735SI8GBGB5.0 Pre-programmed ParametersFP735Si is delivered with a set of pre-programmed parameters. 5.1 Advanced ProgrammingThe following pre-progr

Danfoss Heating9GBGBEvent Time Room heating/water heating status1 06:30 ON2 08:30 OFF3 11:30 ON4 13:30 OFF5 16:30 ON6 22:30 OFFWeekends (Saturday-Sund